Synlube viscosity?

quote:

Originally posted by inHaliburton:

quote:

Originally posted by Taterandnoodles:
Viscosity, ASTM D 445
cSt @ 40º C; (mm2/sec) 100.4
cSt @ 100º C; (mm2/sec) 17.55

Taterandnoodles, not having attended a school of higher learning on this subject, can you decipher for me?

quote:

ASTM D445
Significance and Use

Many petroleum products, and some non-petroleum materials, are used as lubricants, and the correct operation of the equipment depends upon the appropriate viscosity of the liquid being used. In addition, the viscosity of many petroleum fuels is important for the estimation of optimum storage, handling, and operational conditions. Thus, the accurate determination of viscosity is essential to many product specifications.

1. Scope



1.1 This test method specifies a procedure for the determination of the kinematic viscosity, ν, of liquid petroleum products, both transparent and opaque, by measuring the time for a volume of liquid to flow under gravity through a calibrated glass capillary viscometer. The dynamic viscosity, η, can be obtained by multiplying the kinematic viscosity, ν, by the density, ρ, of the liquid.

Note 1—For the measurement of the kinematic viscosity and viscosity of bitumens, see also Test Methods D 2170 and D 2171.

Note 2—ISO 3104 corresponds to Test Method D 445.


1.2 The result obtained from this test method is dependent upon the behavior of the sample and is intended for application to liquids for which primarily the shear stress and shear rates are proportional (Newtonian flow behavior). If, however, the viscosity varies significantly with the rate of shear, different results may be obtained from viscometers of different capillary diameters. The procedure and precision values for residual fuel oils, which under some conditions exhibit non-Newtonian behavior, have been included.

1.3 The range of kinematic viscosities covered by this test method is from 0.2 to 300 000 mm2/s (see Table A1.1) at all temperatures (see 6.3 and 6.4). The precision has only been determined for those materials, kinematic viscosity ranges and temperatures as shown in the footnotes to the precision section.

1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

quote:

Originally posted by inHaliburton:

quote:

Originally posted by Nucleardawg:
Synlube recipe: Wally world oil 'on sale' + witches brew of additives, shake well...Voila, Synlube.

Can you tell us where you got this info? Is it accurate?

quote:

er the synlube PDS bruce tested both samples using the same standard used by synlube.
----------------------------------------------------------------------------------------
SynLube Lube-4-Life® INITIAL FILL - Motor Oil ( UNIVERAL VERSION )

GENERAL INFORMATION

quote:

Originally posted by Taterandnoodles:
Per the synlube PDS bruce tested both samples using the same standard used by synlube.
----------------------------------------------------------------------------------------
SynLube Lube-4-Life® INITIAL FILL - Motor Oil (Universal Version)

GENERAL INFORMATION
Physical State: Viscous Liquid
Color: Opaque Black
Odor: Characteristic
Odor Threshold: N/D

Viscosity, ASTM D 445
cSt @ 40º C; (mm2/sec) 100.4
cSt @ 100º C; (mm2/sec) 17.55

HTHS Viscosity, mPa•s @ 150ºC, ASTM D 4683 5.0
Viscosity Index 201
SAE Viscosity (J300) 5W-50
ISO Viscosity 100
MRV at -35ºC 27,653
Viscosity Index 201
SAE Viscosity 5W-50
ISO Viscosity 100


Sulfated Ash, wt%, ASTM D 874 0.02
Phosphorous PPM 1000

Pour Point, ºC, -45
Boiling Point, ºC, 316
Flash Point, ºC, ASTM D 92 275.8



Density @15º C kg/l, ASTM D 4052 0.926
Vapor Density (Air = 1): > 2 at 101 kPa
Vapor Pressure: at 20°C < 0.013 kPa (0.1 mm Hg)
Total Base Number (TBN) 11.8
Solubility in Water: Negligible

quote:

Originally posted by Nucleardawg:
You guys crack me up!! So the pictures show INITIAL FILL. So there is a UNIVERAL version of the INITIAL FILL? On page 66 of the original SYNLUBE thread even MIRO acknowledges, that he sold the bottle of INITIAL FILL to Tatar. that was tested by BRUCE.

Why do you constantly lie? Even MIRO says he sold the INITIAL FILL.

This info is on page 66 as I mentioned.

So the 'SYNLUBE SHUFFLE' continues.

quote:

Originally posted by Nucleardawg:
Mods since the lies from Captain Kirk continue, perhaps it's time to ban, any mention of Synlube on this site, along with the cheerleader's for this product.

quote:

Originally posted by Captain Kirk:

quote:

er the synlube PDS bruce tested both samples using the same standard used by synlube.
----------------------------------------------------------------------------------------
SynLube Lube-4-Life® INITIAL FILL - Motor Oil ( UNIVERAL VERSION )

GENERAL INFORMATION

This shows universal nuke!!

quote:

Originally posted by vitual_mage:
User ? Where on the magic synlube site? Yeah right…..try harder; funny if I check your post you join only 2 month before Miro during the same year.....and in 5 year did almost only talk about synlube.

I hope mods will close this one quick; even Fox Mulder in x-files was more credible when he was saying do you believe.

quote:

Originally posted by Captain Kirk:
[QUOTE]Originally posted by Nucleardawg:
Mods since the lies from Captain Kirk continue, perhaps it's time to ban, any mention of Synlube on this site, along with the cheerleader's for this product.

quote:

This is not my thread......I did not open it and only posted later on......

I will now stop posting because you are now once again hurling insults..........and you guys can now entertain yourselves once again............later!!!

HAVE FUN!!!!!!!!!!!!!!!!!!