Skip to main content

Read our primer articles on High Mileage Oil, Synthetic Oil and Kinematic Viscosity

For those of you who think that ARX is cleaning up your engine by virtue of the filter media.....

QUOTED..
"ARX's lanolin esters are semi-solid and rather large particles. I have filtered the virgin product with coffee filters which caught a lot of these particles on the filter. It looked like jelly and I think that this is what you are seeing here."

THE LINK

fficial%26channel%3Ds%26ndsp%3D20%26tbs%3Disch:1" target="_blank">http://www.google.com/imgres?i...%3D20%26tbs%3Disch:1
They'll call it a small problem, replace the filter and send the customer a qt of oil. Once the oil lite comes on the damage has been done. It might not be immediate, and that's Amsoil's out, but damage has been done.

How much once again Amsoi's out and anyones's guess. A year two down the road if the car starts blowing smoke or using oil you think Amsoil will help? I don't.

I'll stick with what I can buy locally and change when the mfg suggests. Extended drain oils and filters are not my cup of tea.

Good point Trajan: The last thing Miro wants is anything floating to the surface about his oil. Somethings are best left at the bottom of the sea!

AD
quote:
Originally posted by ADFD1:

I'll stick with what I can buy locally and change when the mfg suggests. Extended drain oils and filters are not my cup of tea.
AD


No reasonable person should have a problem with that. Quality dino/synth oil and filter along with a reasonable oci is the way to go.

Too many links have been posted that show what happens when you don't.

I'm going to try a 10K oci with a filter change when I add oil. (Burn a qt @6k)
Trajan quoted..
quote:
I'm going to try a 10K oci with a filter change when I add oil. (Burn a qt @6k)



AAHHH...the truth comes out once again! You burn oil,and have sludge/varnish issues(You admit to using A-RX).............GOTCHA !!!!!



So, let's sum up your "STELLAR" results with this..........the so called "MFG APPROVED OIL" you're using and swear by.... is really working out well I see.......engine is burning the stuff,and the oil also sludge/varnishes up the engine. All those 'expensive' oil changes with your "Approved oil",and all the flushes,rinses,chemicals,TCW3 in the fuel(don't tell BMW/EPA),etc,etc,............SOUNDS LIKE YOU HAVE PROVEN MY POINT QUITE WELL-conventional wisdom/techniques don't work so well...do they!


The above issues Trajan is dealing with,is the reason why I use Synlube.

I have zero sludge,zero varnish,(zero oil burning/loss/evaporation),no chemicals or flushes ever needed,and No worries!
Last edited by captainkirk
These are all quotes from the 'other site',where everyone is still hung up on VOA,and lab results being unreliable.
-------------------------------------
"As for “simple” VOA and UOA Lab results, they are traditionally variable. Those from Oil Company Labs when testing their own products are certainly better. At a recent visit to Daimler AG in Unterturkheim, I was assured that they do their own VOAs on FF lubricants as a matter of course. Variances in supply quality do occur!

and the 0w-40 is not synthetic basestock? also, viscosity as published is an average value not an exact one. look at

Yes. Most oil companies give averages on their PDS sheets and UOA's all depend on the calibration of the test equipment and which human did them. I've had VOA's done in the past where I questioned the additive level. Resent samples three times from the same bottle and got back three different answers. All within the 10% range

The Blackstone 100C vis of 13.36 cSt is quite a bit off the M1 PDS spec' of 14.0 cSt (used to be 14.3 in the not too distant past).
That's something to keep in mind when reviewing UOAs from this lab particularly when assessing how shear prone M1 0W-40 is reported to be.


This seems to happen far too often. I know VOA/UOA are relatively inexpensive via Blackstone but having to send out a sample to verify a sketchy result does add up. It seems the adage "you get what you pay for" does apply to oil analyses. "

VOA's are not a good way to answer your question Shup1. They are good to have for reference in comparison to UOA's to see what changes occured during use. You cannot rate an oil bt its VOA


Some might be close, but when a VOA is even over a year old, it's pretty much old news. When a VOA is 4+ years old, there is almost 100% certainty it been changed by the formulator. Driven by improvement, specification chasing, cost, new and discontinued additives - lubricant formulas change.


--------------------------------------------------------------------------------

SAVE YOUR MONEY GUYS. ......ALL THAT REALLY MATTERS IS LONG TERM PERFORMANCE,AND ACTUAL RESULTS!!! THOSE TESTS(VOA/UOA) ARE CERTAINLY GOOD AT DRAINING YOUR WALLETS-IF NOTHING ELSE! THAT'S WHY I HAVE NEVER BOTHERED!
Last edited by captainkirk
quote:
Originally posted by ADFD1:
Kirk- I hardly think Trajan has a problem. Burning a qt of oil in 6000 miles is not considered a problem. A car mfg considers oil consumption a problem when an engine uses more than 1 qt/1000 miles, anything else is considered normal.

AD


You're right. It isn't a problem. It's far from a problem. The dealer doesn't see it as a problem. My mechanic doesn't. People who own and drive these cars, unlike kirk, don't see it as a problem.

No synlube, no worries.
quote:
Originally posted by Trajan:
[QUOTE]Originally posted by ADFD1:
Kirk- I hardly think Trajan has a problem. Burning a qt of oil in 6000 miles is not considered a problem. A car mfg considers oil consumption a problem when an engine uses more than 1 qt/1000 miles, anything else is considered normal.

AD


You're right. It isn't a problem. It's far from a problem. The dealer doesn't see it as a problem. My mechanic doesn't. People who own and drive these cars, unlike kirk, don't see it as a problem.

-------------------------------------------

Well...then your all blind...or ignoring the obvious! Your engines are not in stellar condition.

If I were the dealer, I would also tell you the car is fine,and then say........"have a nice day and be sure to come back when the warranty runs out--and your ready for an engine overhaul"............OUT OF WARRANTY OF COURSE! LOL
Just a simple question:

Why is $46,000 car worth only $14,000 when it runs out of the 4 year 50,000 miles Warranty ?

That is the $32,000 question !!!

May be there is reason for it = it is BMW....

The Ultimate sucker machine, and the fact that it sucks oil too; is just part of the "Unique owner Experience".


Infact BMW depreciation rate is just about the same as that of a HYUNDAI, i.e. in used car business it is valued the same, that alone should be a clue.

(Except for MINI which while sold by BMW dealers from spearate showroom is not real BMW - fortunately, and thus it has the hihgest reseale value in the car industry)
quote:
Originally posted by ADFD1:
All cars depreciate, it's called reality. How about those Yugos? What a joke they were.

AD


The explaination goes over his head. He should also realize that, in time, many cars do increase in value. Depends on many things though.

A pristine 1969 Camaro with the right options is worth more than a new 2011 model. Today, an old Isetta, well, http://autos.aol.com/used-list...-BMW/model1-Isetta/, which is far more than it costs when new.

He's only frothing at the mouth due to the very harsh light we've thrown on synlube. and the product came up short.

I would also explain to him that the 15K service on a BMW is much more than a simple oil change. But that would go over his head too.

We all know what a Yugo is worth. Even an Edsel is worth far more.

I also see that, and there is no surprise there, that once again, he can't back his "claims".

A free hint miro. Making fun of BMW doesn't faze me. Just displays the on going ignorance you convey. Good for a laugh or two.

Yugos sell for what, $100, if that now?
Last edited by trajan
BMW uses low tension piston ring sets on purpose. They provide less parasitic drag on the cylinder walls and superior cylinder lubrication at high RPM high load. Small and large high specific output engines from many brands use this strategy. Not a problem. They are designed this way for A reason. Its not the oils fault they chose this engineering compromise.
KBB values based on real transaction prices in 2010

BLUE BOOK® PRIVATE PARTY VALUE
Close
Private Party Value
Kelley Blue Book Private Party Value is the amount a buyer can expect to pay when buying a used car from a private party. The Private Party Value assumes the vehicle is sold "As Is" and carries no warranty (other than any remaining factory warranty). The final sale price may vary depending on the vehicle's actual condition and local market conditions. This value may also be used to derive Fair Market Value for insurance and vehicle donation purposes.

1990 YUGO GV Value

Excellent $2,300
Good $2,150
Fair $1,650

Not bad for a car that was $5,225 MSRP and sold for about $4,900 in 1990 to be worth that much 20 years later.

This is data from the came company that depreciates BMW 62% in the first year of ownership, while MINI is worth 62% of its price 36 months later.

But still YUGO tops the list it is worth 41% of its original price (if not beat up) 20 years LATTER !!!

Compare that to most cars that are worth that much (less) just in 12 to 18 months !!!
Compare that with BMW and that is one of the "top" models: 2010 BMW M6
MSRP $$106,225.00
New 100% $102,350.00
2 45% $46,057.50
3 37% $37,869.50
4 30% $30,705.00
5 24% $24,564.00

It is 45% of its value after just 12 months, dont you wish you have YUGO ? It's value drops almost $4,000 even before it is driven off the dealer's lot - how is that for a "great" car ?
MY point of all of this is, in case you have missed it:

Great vehicles no matter the make or model retain its value over time.

Poor vehicles lose their value very very quickly.


As simple as that.

If BMW retained it's value Trajan would not be able to afford even the used one.


NO ONE Can argue with that, the data is there and available to every one, but if you elect to stick your head into a sand dune that of course is you privilege.

Similarily data is availalble about the problems conventional lubircants cause, like sludge, gel, varnish, excessive oil consumption, and so on.

I accept the fact that BMW may have "special" low tension rings, but that does not explain why cars converted to a better lubricant at low mileage DO NOT consume much oil, while those serviced at BMW for FREE do develop such "problem" when the warranty is over or in just 50,000 miles.

NO one seems to report that their car lost 2 quarts or more before the FIRST service was due, but by 45,000 iles the same vehicle "burns" oil - WHY ???

May be the 15,000 + service intervals are just TOO LONG for the stuff the BMW dealers use in these vehicles.

Clearly when the engine leaves the BMW assembly it is as perfect as can be, it is only latter that it develops the "oil consumption", so something DOES NOT last.

And if the oil you use makes a difference then of course it is lubrication related issue.

Well actually more like Tribological Issue as friction, wear and lubrication all play a role in that scenario.

And do not think of this as SynLube promotion, simple as I have stated before we have BMW customers that did not use the FREE BMW service and NONE have oil consumption issues, while those that waited for the FREE and WARRANTY to expire FIRST before they switched all are asking why is my car burning so much oil.

It is not one in many vehclies issue; it is statistically proveable trend with identical experience shared my many.

Just search the web -------
I find it quite funny reading this. Miro are you trying to say a Yugo is a better car than a BMW? Then trying to make the case for your oil?

Bad move, pick another car, YUGO was/is a POS. You're not selling your oil by pointing out that Yugo is a good car. People vote with their check books, and YGUO failed horribly in the USA. Anyone I ever heard talk about them called them throw away cars, and garbage. I think most here will agree?

Lets take a vote: Pick a car to own, anything from BMW, or anything from YUGO?

Then or now?

I'll sound off with BMW.

AD
Just to further the fact that miro doesn't know what he's talking about

Oil Service 15,000 miles

Replace oil and filter
Reset service indicator
Check front brake pads
Check rear brake pads
Check parking brake operation
Replace cabin air filter

Inspection 1 30,000 miles or 24 months (whatever is first)

The above, plus:

Check manual transmission fluid level. (If equipped)
Check all underhood componets/hoses for fluid leaks.
Check and drivebelts and replace if necessary.
Check steering and suspension components.
Check exhaust systems and mountings.
Check condition and operation of seatbelts.
Check headlight beam alignment.
Check operation of headlight/windshield washer system.
Check engine management system.
Road test.

45,000 miles/36 months

Repeat oil service.

60,000/48 months: Inspection II

repeat Ins 1
Replace spark plugs
Check drive shaft boots.

There's more to it,Like air filter changes, but it's more than the oil change he claims.

What he also doesn't mention is that the dealer arranges a loaner car for you. (I've had two 3 series sedans and a new Toyota Camry. The guy who owns the BMW dealership also owns the Toyota and Lexus dealership next to each other.)

You can of course wait at the dealer, but they give you a free loaner, so why bother.
quote:
Originally posted by BKL98MK8LSC:
BMW uses low tension piston ring sets on purpose. They provide less parasitic drag on the cylinder walls and superior cylinder lubrication at high RPM high load. Small and large high specific output engines from many brands use this strategy. Not a problem. They are designed this way for A reason. Its not the oils fault they chose this engineering compromise.


Very well said. Also, I didn't know that. Thanks!!
Last edited by trajan
quote:
Originally posted by ADFD1:
Since the tolerances are so much better and engines tighter, I'd stay clear of that 50 grade oil you're pushing and follow mfg specs, using an approved oil.


No point mail ordering anything, pick a good synthetic oil from a reputable company and have at it.


AD


One of his own links states that one way to combat sludge is to use the correct viscosity. Using synlube in a Mustang isn't it.
quote:
Originally posted by Trajan:
quote:
Originally posted by Miro Kefurt:
My Drop to the bucket:

Just like oil will surface to the surface no matter what BP may claim about it, lies and deceptions will eventually surface too.



So synlube like..........


So Trajan like. Where's that engine belonging to you neighbour that sludged-up using Synlube, eh Big Mouth?

Well?
quote:
Originally posted by Trajan:
You're right. It isn't a problem. It's far from a problem. The dealer doesn't see it as a problem. My mechanic doesn't. People who own and drive these cars, unlike kirk, don't see it as a problem.

No synlube, no worries.


Dirty engine. Burns oil. Using ARX to fix. Blame the original owner. No problem. BMW says so. No problem. Mechanic say so. No problem. What me worry? Alfred E. Newman = Trajan.
6000 miles and a qt of oil is needed, come on guys lets get real. That is not oil burning.

With all the positive press 3 people are giving Synlube, only two of them are using it. One of them owns the company. The other a shill. How come no one else is stepping up to the plate? Probably because most people reading about it realize what it's all about.

AD
fowvay quote...

I used this stuff after reading an article in European Car. At least I think it was European Car magazine back then.... anyhoo...

I put it in my 1986 Jetta Diesel at 121,000 miles and installed a canton mecca remote oil filter at the same time. I changed the filter every 25,000 miles and added a quart of oil at that time.

I sold the car at 486,000 miles after it was rear ended by a Chevy Chevette doing 45mph. It still ran great and delivered a solid 42mpg in the city (redline to redline shifts) and averaged a healthy 52mpg at 70mph.

I did change the oil out every 50,000 miles as per there directions back in the early 90's and allthough extremly black it still was performing very well and there was no sludge build up anywhere.

I thought the company had fallen off the face of the Earth or had gone out of business. That is untill today when I came across a link to it from another website.

I will try it out first in our Ford Focus since it sees the most use. I will report back in 2 years when it had accumalted 50,000 miles and let you know the averages.
__________________
My 1.8T New Beetle "Pomelo" | Fowvay2000 | My 1970 Bug "Oscar"
"How to" Light your bud vase | "How To" Get your trunk to pop open & Fix that trunk rattle
Instant liter per 100km to mpg converter | Tire size calculator | "How to" install Audi TT dash vents
"How to" replace your broken antenna base | "How to" replace your brakes | "How to" remove your head lights
Fowvay2000 is offline Reply With Quote


-------------------------------------------

jonny-b-quote

Hi, Gary Allan. I will also take a VOA and send it in together with the UOA. I have been driving 10000 km(6200 miles) now, since I filled my old Nissan with Synlube. All I can say now, is that this seem to be the best oil I have ever used. However, this is based on sounds from the engine being gradually reduced, how the engine idles and how I think it performs,as well as a slight reduction in fuelconsumption. I will do a lot of driving this summer, so I was planning to send in a UOA when I reach some 20K miles.
I also have ordered their gear oil, and already have their oil in the diff. I also ordered their microglass filter, and I will replace the OEM Nissan oil filter with this. I don't think you can go wrong, by using their products, but if anyone can give some info proving otherwise, I would be glad to know. In the meantime, I keep on driving to test it.


And Many,many others like myself and so forth have been using synlube for many years now.........
Last edited by captainkirk
quote:
Originally posted by ADFD1:
6000 miles and a qt of oil is needed, come on guys lets get real. That is not oil burning.

With all the positive press 3 people are giving Synlube, only two of them are using it. One of them owns the company. The other a shill. How come no one else is stepping up to the plate? Probably because most people reading about it realize what it's all about.

AD


Why doesn't inhaliburton step up to the plate???????

Yep. it's far from oil burning. Especially when you consider what BKL pointed out. Which I'll post again since they *still* don't get it:

*****Originally posted by BKL98MK8LSC:
BMW uses low tension piston ring sets on purpose. They provide less parasitic drag on the cylinder walls and superior cylinder lubrication at high RPM high load. Small and large high specific output engines from many brands use this strategy. Not a problem. They are designed this way for A reason. Its not the oils fault they chose this engineering compromise.*****

The problem these three have is that no one, either here or at bitog, is jumping on their bandwagon.

Still a mystery why one of the fans fears to use it. Or why the other two don't go after him.

Only someone who knows nothing about BMWs, or cars in general, would find 1qt/6k a problem.
A few years ago: http://www.pistonslap.com/tsb/010601011A.pdf

The accepted rate of oil consumption for engines used in the vehicles referenced is 0.946
liter (1 qt) in 3200 km (2000 mi). This rate only applies to personal use vehicles, under
warranty, maintained in accordance with the appropriate maintenance schedule, with less
than 58,000 km (36,000 mi), or 80,450 km (50,000 mi) for Cadillac, driven at legal
speeds in an unloaded (for trucks) condition.

Oops, they've been skunked again.

They probably feel the same way about Mazda's rotary engine as well.

A sure fire sign you're burning oil is the cloud of blue smoke. Don't have that.

I should also point out that none of my three fans stuck their beaks in this thread until *after* I chose the oil. Very telling.
Last edited by trajan
quote:
Originally posted by Captain Kirk:
quote:
Originally posted by Trajan:

Maybe kirk should read this again?

*******Originally posted by BKL98MK8LSC:
BMW uses low tension piston ring sets on purpose. They provide less parasitic drag on the cylinder walls and superior cylinder lubrication at high RPM high load. Small and large high specific output engines from many brands use this strategy. Not a problem. They are designed this way for A reason. Its not the oils fault they chose this engineering compromise. ********



I already explained the ring pressure issue. Here it is again.


This low ring pressure is not an engineering compromise.......it's an engineering achievement!

All engineering is a combination of compromises. It is possible to go to far with any of them. The best choices are a matter of constant debate and tend to become self evident over time through successes ,failures or plain mediocrity. Some companies are better at making these decisions than others. The same goes for oil companies and car companies.
Ah yes, ole jonny b. The guy who insulted anyone who dared question synlube. Or any other miracle in a can..... never did that VOA/UOA.

Just like inhaliburton. a guy who not only still defends a swill known as synlube, but is too scared, lacks the courage of his convictions, isn't man enough, to actually use it.

What can you expect from a child who, being that he lacks any ability, can only do things like make up lies. Find that thread you accussed me of inflicting ruin on yet? Oh, that's right, you made it up.
Last edited by trajan
I think we agree on some points. GM did not go with their own specification because they were happy with API. Being blown off for a period of years makes the general REAL unhappy. What their specific issues are I dont know but certainly it was something. Europe and japan have gone their own way and are not immune to problems. I think the elephant in the room that is causing issues is government regulations. Pressure to reduce waste streams to a minimum got the Europeans to specify long OCI and some got bit. Regulations on VOC emissions here have made crankcase ventilation systems very effective moisture traps. CAFE standards are pushing manufacturers to spec lighter oils than they would otherwise use,even if only slightly. Non of these are deal breakers when all you have to do is change your oil to fix it. Forcing 100000 mile catalytic converter life at the expense of safe reliable engine wear protection and sabotaging older engines with mechanical valve trains is a piss poor use of government power,however well intentioned. The engineering responses to regulation are as varied as can be,some are successful,some not. BMW is not immune to this. The crank case ventilation system on some models can fail in very cold weather and suck all the crankcase oil into the intake manifold and cause engine destruction. Not the oils fault unless you count water trapped in it. When the water freezes the valve fails. These may be the failures your referring to.
quote:
Originally posted by BLK98MK8LSC:

The crank case ventilation system on some models can fail in very cold weather and suck all the crankcase oil into the intake manifold and cause engine destruction. Not the oils fault unless you count water trapped in it. When the water freezes the valve fails. These may be the failures your referring to.


That is a problem in the colder climates. IIRC there is a cold climate version of it. It's insulated IIRC.

FWIW, "normal" PCV valves can have the same thing happen. For instance: http://www.subaruforester.org/...-ltd-heads-up-47434/

Not a problem I have though.
quote:
Originally posted by BLK98MK8LSC:
I wasnt picking on BMW but on the VOC emission regs that dictate sealed up tight crank cases. They trap moisture to the point of build up. Does depend on conditions.


I know, I just didn't see the need to quote the whole post Smile

You may find this of interest:
http://www.bimmerfest.com/foru...wthread.php?t=422965

"To cool the piston crowns directly, nearly all BMW engines are equipped with oil spray jets that moisten the piston crowns with engine oil."

I wasn't aware they had that feature.
Low tension rings for superior cylinder lube. Check.

Oil spray jets for the piston crowns. Check.

Very acceptable oil consumption rates as determined by the people who know what they're doing. Check.

Nobody buying what miro/kirk/inhal sell. Check.

Miro/kirk/inhal displaying their wealth of ignorance on such things. Check and mate.
Post
attend Reliable Plant 2024
×
×
×
×
Link copied to your clipboard.
×